[ Chinese wardrobe net ] Wardrobe is the necessary furniture for the family, often placed in the bedroom, then how to choose the bedroom wardrobe? Let's share the key points and precautions for the choice of bedroom closet. I hope everyone can pay attention when choosing the bedroom closet.
Bedroom wardrobe purchase points
1, first look at the plate
Professional manufacturers use environmentally-friendly plates that meet national testing standards, while some manufacturers use inferior plates that pose a serious threat to human health. Therefore, to buy a wardrobe, you should first check whether there is a sheet inspection report and related inspection certificate.
2, look at the sheet veneer
The surface looks good, however, with a light stroke, you can draw a noticeable scratch. These wardrobes are made of surface-coated vellum paper and ornate paper sheets, which have poor abrasion resistance. Professional manufacturers use environmentally friendly melamine veneers that are treated with high temperature and high pressure, which are resistant to scratches.
3, look at the edge of the board
Professional manufacturers use precision panel saws to cut sheets, and after sealing around them, it effectively prevents moisture in the air from invading the inside of the board. Some manufacturers have no professional equipment, and the cutting is rough, and only one side of the board is seen in front of the edge. The unsealed surface easily absorbs moisture from the air, which can cause the wardrobe to deform and affect the service life.
4, look at the processing method
Professional manufacturers use professional automatic edge banding machines, and the accessories used in the production process are environmentally friendly. Some manufacturers, without professional processing equipment, use ordinary universal glue to manually seal the edges, easy to pull off the drum. This kind of glue contains benzene, formaldehyde and other harmful substances seriously exceeding the standard, posing a potential threat to human health.
5, see the backplane structure
Professional manufacturers use a backing plate with a thickness of 5mm or more, melamine veneer, and a trough-type reverse leather lap joint structure to prevent the back plate from directly absorbing the moisture on the wall surface. Some brands have thin back plates and are connected by nail-type back plates. The back plates are in direct contact with the wall. The moisture on the wall is easily absorbed by the plates, which is easy to get wet, moldy and deformed, and the cabinet loses its seal. Sex.
Three important considerations for buying a wardrobe
Note on the purchase of wardrobes: profiles
There are two types of practical profile substrates: one is aluminum alloy and the other is plastic steel. Due to its light weight and high strength, aluminum alloy is a high-grade material for sliding door substrates. Has gradually replaced plastic steel products. The aluminum alloy itself is divided into ordinary aluminum-magnesium alloy and smaller aluminum-magnesium alloy for special aviation. Because aluminum-magnesium-titanium-silicon alloy has higher strength and smaller weight. Therefore, it is favored by consumers, but the cost is several times that of ordinary aluminum-magnesium alloy. When looking at the profile, not only pay attention to the substrate, but also observe its surface treatment. Advanced surface treatments include anodizing, electrophoretic coating carbon coating, etc. These processes have higher hardness and aesthetics than simple spraying and plating.
Note on buying a wardrobe: top and bottom rails
At the time, try to choose the top and bottom rails of the same material as one material, thinking that the top bottom rail is the load-bearing part. To withstand repeated friction, the top and bottom rails must have high strength and wear resistance. The top and bottom rails are made of aluminum-magnesium-titanium-silicon alloy with higher strength, strong resistance to deformation and longer service life.
Purchase wardrobe notice three: top bottom wheel
The top and bottom wheels are important accessories for sliding doors. It is necessary to pay attention to the selection of high-quality bearing pulleys. The outer part of the bottom wheel is made of FRP material, which has the characteristics of high strength, wear resistance and low noise. Using push-pull more than 100,000 times, the wheel body is treated with three-degree polishing and plating, never rusting.
The above is the key points and precautions for the wardrobe purchase for everyone to share, I hope to be helpful to everyone.
Anji Tianwei Steel and Plastic Products
Co.,Ltd. is a professional Indoor furniture Manufacturer. Since the
foundation in 1998, we've been keeping the idea of making best furniture
for our customers, With 20+ years' rapid growth, we've been in the
leading position among local furniture industry. Today, we have 300
employees and 80000 square meters' workshop. We ship over 200 containers
every month. Our customers are from all over the world. We work with
many retailers and importers.
Our huge productivity and strict
quality control ensure our customers receive best chairs with fast
delivery. We're always focusing on the new trend of chairs, which make
our products keeping abrest of the needs of international market.
In Tianwei, everybody knows his duty and works with passion.
In Tianwei, each customer is well being respected and each order will be tracked and dealed precisely.
We are sure to be your best and reliable partner for chairs and we warmly welcome honorable guests to visit our factory!
Rustic Industrial Bar Stools,Vintage Industrial Bar Stools,Industrial Style Stools,Vintage Industrial Stool
Anji TianWei Steel and Plastic Products Co.,Ltd , https://www.twchair.com