Puro Steidle, Manroland’s board member, said: “Because the new generation Manroland ROTOMAN has advanced components and high productivity, it will not only become the mainstream of 16-page web presses in the next decade. It will also become a hot spot for web printing presses." The new generation of ROTOMAN has a new design and new development, intelligent and other features, such as higher operating performance, faster replacement time, lower waves The waste rate maximizes the quality of the printed matter. In addition, it also provides a high-speed, high-efficiency and high-reliability, gap-free web printing press on the new generation of ROTOMAN. In the 20th century, 70, 80, 90 In the era, ROTOMAN achieved the results of installing 380 lines. In the new century, the new generation of ROTOMAN will undoubtedly continue to develop.
More kinds of cardboard printing range The new generation of 16-page ROTOMAN printing press is very suitable for use in advertising printing, because in the traditional printing, it can provide convenient and quick printing like bread butter, in ordinary printing. , It can provide a smaller amount of print than the traditional mass printing. Depending on the type of board, ROTOMAN can provide two different models with a drum speed of 55,000 rpm and 65,000 rpm, and a corresponding folding system.
Performance Kit means lower boot consumption. In the commercial web printing process, reducing waste is one of the most important aspects of increasing production profit. Manroland provides Performance Kit and its associated software and hardware equipment. It greatly reduces waste during the process of just starting the process, during the printing process and during the printing process, and improves the production efficiency. At Drupa, ROTOMAN assembled QuickStart 2 on-site. In the demonstration process four times a day, the number of scrap pages was less than 800 during the boot process after the change. Currently, the QuickStart 2 is already installed in various models of the ROTOMAN and can be used in independently driven ROTOMAN printers.
Quickly open the installation of QuickStart 2 to make it possible to print the product in a short time. After installing the intelligent start-up and shut-down control system, the printing unit can adjust the machine faster, enter the printing state, and reduce the waste as much as possible. This is caused by the Ink supply unit (ink-squeegee system). And subsequent pre-inking system guarantees. The automatic ink bar also makes the system adjust the ink faster. Automatic blanket cleaning and drying devices are also equipped with automatic devices that start and stop the printing press. Therefore, the boot printing waste no longer exists in the printing.
Telelink2 can improve efficiency more quickly The second module, Telelink2, can calculate production parameters through the Tele Support Centre to increase production efficiency. This calculation function includes preparation of production parameters, production analysis and statistical calculations. In order to further improve the production process and reduce errors, it is necessary to analyze downtime, obtain information, and output characteristic parameters. In this way, the characteristics of the production process are measured and can be accurately measured to improve machine performance.
Quality Kit for High-Performance Color Control In the modern web commercial printing process, stable high-quality printing must be maintained, but such as ink density, temperature, wetting system, paper properties, blankets, plates, etc. Changes in one of many factors can cause changes in the printing results. To control and correct these changes, Manroland and QTI and Brunner jointly developed the Quality Kit, a device for automatic ink control. This system can be intelligently controlled through the PECOM ColorLoop interface. The size of the outlets may be automatically controlled by the PECOM unit. In this system, CCS is responsible for the automatic control of ink density, Aviator for gray balance measurement, automatic ink density control, and product quality analysis according to the Brunner standard. Intrument Flight automatically controls multiple parameters according to the Beunner system.
Perfect printing becomes possible The Intrument Flight software on the Brunner system can determine and analyze more than 30 variable processes. For automatic color control, it only needs to print about 2.5mm color bars on the web. During operation, one lens will record the density and gray balance parameters of the ink sticks passing through, and thus, printing in Manroland. On the machine, the entire printing process will be very fast and automatic color control, quickly reduce the supply of ink. This also enables the manroland press to maintain the most consistent high quality printing on a minimal waste basis.
Save paper The new 16page ROTOMAN web press offers different cutting sizes such as 578mm, 598mm, 620mm and 965mm. It can be said that the common print sizes in Europe, North America, North America, and Asia have all been covered. Especially when the price of paper keeps rising, the 620mm size print can even produce full-bleed DIN A4 small format products.
Automatic plate change within 5 minutes The fully automatic plate change system PPL is the standard configuration of the new ROTOMAN. Its biggest feature is that it is possible to continuously reel in the plate change. In this way, eight plates are also changed in five minutes. Can be completed within. The PPL has been applied in Manroland's 1000 production units and its installation has also greatly increased the level of automation in production.
The blanket blanket that is saved is a major aspect of consumption in printing. In the new ROTOMAN, despite the printing speed of 65,000 revolutions per hour, it also allows the use of ordinary blankets, which have a clearance of only 5.5 mm. Manroland uses the sleeve technology.
The above features will make ROTOMAN in use, will meet your needs as much as possible, making it a popular press in the new century.
More kinds of cardboard printing range The new generation of 16-page ROTOMAN printing press is very suitable for use in advertising printing, because in the traditional printing, it can provide convenient and quick printing like bread butter, in ordinary printing. , It can provide a smaller amount of print than the traditional mass printing. Depending on the type of board, ROTOMAN can provide two different models with a drum speed of 55,000 rpm and 65,000 rpm, and a corresponding folding system.
Performance Kit means lower boot consumption. In the commercial web printing process, reducing waste is one of the most important aspects of increasing production profit. Manroland provides Performance Kit and its associated software and hardware equipment. It greatly reduces waste during the process of just starting the process, during the printing process and during the printing process, and improves the production efficiency. At Drupa, ROTOMAN assembled QuickStart 2 on-site. In the demonstration process four times a day, the number of scrap pages was less than 800 during the boot process after the change. Currently, the QuickStart 2 is already installed in various models of the ROTOMAN and can be used in independently driven ROTOMAN printers.
Quickly open the installation of QuickStart 2 to make it possible to print the product in a short time. After installing the intelligent start-up and shut-down control system, the printing unit can adjust the machine faster, enter the printing state, and reduce the waste as much as possible. This is caused by the Ink supply unit (ink-squeegee system). And subsequent pre-inking system guarantees. The automatic ink bar also makes the system adjust the ink faster. Automatic blanket cleaning and drying devices are also equipped with automatic devices that start and stop the printing press. Therefore, the boot printing waste no longer exists in the printing.
Telelink2 can improve efficiency more quickly The second module, Telelink2, can calculate production parameters through the Tele Support Centre to increase production efficiency. This calculation function includes preparation of production parameters, production analysis and statistical calculations. In order to further improve the production process and reduce errors, it is necessary to analyze downtime, obtain information, and output characteristic parameters. In this way, the characteristics of the production process are measured and can be accurately measured to improve machine performance.
Quality Kit for High-Performance Color Control In the modern web commercial printing process, stable high-quality printing must be maintained, but such as ink density, temperature, wetting system, paper properties, blankets, plates, etc. Changes in one of many factors can cause changes in the printing results. To control and correct these changes, Manroland and QTI and Brunner jointly developed the Quality Kit, a device for automatic ink control. This system can be intelligently controlled through the PECOM ColorLoop interface. The size of the outlets may be automatically controlled by the PECOM unit. In this system, CCS is responsible for the automatic control of ink density, Aviator for gray balance measurement, automatic ink density control, and product quality analysis according to the Brunner standard. Intrument Flight automatically controls multiple parameters according to the Beunner system.
Perfect printing becomes possible The Intrument Flight software on the Brunner system can determine and analyze more than 30 variable processes. For automatic color control, it only needs to print about 2.5mm color bars on the web. During operation, one lens will record the density and gray balance parameters of the ink sticks passing through, and thus, printing in Manroland. On the machine, the entire printing process will be very fast and automatic color control, quickly reduce the supply of ink. This also enables the manroland press to maintain the most consistent high quality printing on a minimal waste basis.
Save paper The new 16page ROTOMAN web press offers different cutting sizes such as 578mm, 598mm, 620mm and 965mm. It can be said that the common print sizes in Europe, North America, North America, and Asia have all been covered. Especially when the price of paper keeps rising, the 620mm size print can even produce full-bleed DIN A4 small format products.
Automatic plate change within 5 minutes The fully automatic plate change system PPL is the standard configuration of the new ROTOMAN. Its biggest feature is that it is possible to continuously reel in the plate change. In this way, eight plates are also changed in five minutes. Can be completed within. The PPL has been applied in Manroland's 1000 production units and its installation has also greatly increased the level of automation in production.
The blanket blanket that is saved is a major aspect of consumption in printing. In the new ROTOMAN, despite the printing speed of 65,000 revolutions per hour, it also allows the use of ordinary blankets, which have a clearance of only 5.5 mm. Manroland uses the sleeve technology.
The above features will make ROTOMAN in use, will meet your needs as much as possible, making it a popular press in the new century.
Digital Printing machine Co., Ltd. , http://www.hfuvprinter.com